Atdec Telehook TH-WH-PJ-FM Installation manual Manuel d'utilisateur télécharger pdf

Component Checklist

Roll / Shift Adjustment

Component Checklist

Check you have received all parts against the Component Checklist above.

Bits Bag

WARNING

WARNING: This bracket supports up to 15kg (33lbs).

DO NOT overload this bracket.

Ensure the Ceiling can support the total weight of the Projector and the Universal Flush Mount.

All bolts and screws must be used at the designated points in the installation instructions to prevent damage

to the projector, or personal injury.

DO NOT install near air conditioner vents or where there is excessive dust or smoke.

Ensure the projector is mounted so that it is not possible for excessive loads to be placed on the bracket.

Extension Brackets

150mm (x 2)

Extension Brackets

75mm (x2)

Square Nut (x8)

Cross Recessed Screws

M2.5x15 (x4)

M3x15 / M3x20 (x4 each)

M4x15 / M4x20 / M4x25 (x4 each)

M5x15 / M5x20 / M5x25 (x4 each)

M6x15 / M6x20 / M6x25 (x4 each)

M5x10mm

Socket Button

Cap Screw (x4)

Spacer

Large (x4)

Medium (x4)

Small (x4)

6mm Allen

Key (x1)

Bottom

Spacer (x4)

Flush Mount

Assembly (x1)

Nylon Anchor

Plug (x2)

Washer

20mm (x2)

10mm (x4)

8mm (x4)

14 Gauge Coach Screw (x2)

Allen Key

6mm

M8x50mm

Socket Cap

Screw

M8 Nyloc Nut

Ceiling Plate

Locking Hook

Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 03.02.09©

F.1.

Connect the Shaft to the Ceiling Plate as shown

below.

Installation Instructions

Please read these

instructions before

commencing installation

as faulty installation could

result in injury. Atdec

assumes no responsibility

for faulty installations.

IMPORTANT

Removing the Ceiling Plate from the Flush Mount Assembly

Attaching the Flush Mount Assembly to the Ceiling Plate

Adjusting the Projector

Installation Complete

F.3.

Tighten the Locking Hook with the M8x50mm

Socket Cap Screw and the M8 Nyloc Nut that

was previously removed.

F.2.

Insert the

Locking Hook

into the slot in

the Ceiling Plate

to lock the Flush

Mount Assembly.

Ceiling Plate

Locking

Hook

M8 Nyloc Nut

M8x50mm

Socket Cap

Screw

Locking

Hook

6mm

Allen Key

Flush Mount

and Projector

M8x15mm

Screw

6mm

Allen Key

6mm

Allen Key

Remove the Ceiling Plate from

the Flush Mount Assembly as

shown.

Pitch Adjustment

Loosen

Tighten

3mm Allen

Key (x1)

To make Roll/Shift adjustments, first ensure the

weight of the projector is supported. Then loosen

the M8x65mm Screw with the supplied 6mm Allen

Key, and adjust to your desired position.

Re-tighten the screw firmly.

To make Pitch adjustment, first ensure the weight

of the projector is supported. Then loosen both

M8x15mm Screws with the supplied 6mm Allen

Key, and adjust to your desired position.

Re-tighten both screws firmly.

6mm

Allen Key

M8x65mm

Screw

Loosen

Tighten

SHIFT

Shaft

Extension

Brackets

100mm (x2)

Extension

Brackets

50mm (x2)

Tip: When the projector requires servicing, remove

the projector via this easy disconnection point to

save time.

Pitch

Roll Roll

Projector Ceiling Mount |Flush

1 2

Résumé du contenu

Page 1 - Installation Instructions

Component ChecklistRoll / Shift AdjustmentComponent ChecklistACheck you have received all parts against the Component Checklist above.Bits BagWARNINGW

Page 2 - Masonry Plaster Board

Centre of Flush MountCentre of GravityExtension BracketBottom SpacerSpacer Recessed Mounting HoleD.1.Pick up the projector using both of your index fi

Commentaires sur ces manuels

Pas de commentaire

Atdec Telehook TH-WH-PJ-FM Installation manual Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Projecteurs Atdec Telehook TH-WH-PJ-FM Installation manual. Atdec Telehook TH-WH-PJ-FM Installation manual User Manual [fr] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Projecteurs Atdec Telehook TH-WH-PJ-FM Installation manual